Session Table Processing Agency = MIT Satellite Constraint = Y ; Y/N (next two lines are free-format but 'all' must be present) all a e i node arg per M rad1 rad2 rad3 rad4 rad5 rad6 rad7 rad8 rad9 0.01 0.01 0.01 0.01 0.01 0.01 1.0 1.0 0.01 0.01 0.01 0.01 0.01 0.01 0.01 Choice of Experiment = RELAX. ; BASELINE/RELAX./ORBIT Data Status = RAW ; RAW/CLN Type of Analysis = 1-ITER ; 1-ITER/0-ITER (no postfit autcln)/PREFIT This now redundant AUTCLN Postfit = R ; Run autcln for postfit run; R causes repeat run. Choice of Observable = LC_AUTCLN ; L1_SINGLE/L1&L2/L1_ONLY/L2_ONLY/LC_ONLY/ ; L1,L2_INDEPEND./LC_HELP/LC_AUTCLN Initial ARC = Y Wobble Constraint = 0.01 0.01 ; Tighten to 3 mas (10 cm) and .1 mas/day for small network UT1 Constraint = 0.00001 0.01 ; Tighten to .1 s/day (5 cm/day) for small network Station Error = ELEVATION 10 5 ; 1-way L1, a**2 + (b**2)(L**2) in mm, ppm, default = 10. 0. Ionospheric Constraints = 0.0 mm + 8.00 ppm Met obs source = GPT 0 ; hierarchical list: RNX ufile GPT/STP [humid value] ' to match 10.2, use STP 50; new default is GPT 50 Output met = N ; write the a priori met values to a z-file (Y/N) Use met.list = N Use met.grid = N DMap = GMFH ; GMF(default)/NMFH/VMF1 WMap = GMFW ; GMF(default)/NMFW/VMF1 Use map.list = N Use map.grid = N Zenith Delay Estimation = YES ; YES/NO (default no) Atmospheric gradients = YES ; YES/NO (default no) Gradient Constraints = 0.01 ; gradient at 10 deg elevation in meters; default 0.03 m Number Zen = 13 ; number of zenith-delay parameters Zenith Constraints = 0.50 ; zenith-delay a priori constraint in meters (default 0.5) Zenith Variation = 0.02 100. ; zenith-delay variation, tau in meters/sqrt(hr), hrs (default .02 100.) Zenith Model = PWL ; PWL (piecewise linear)/CON (step) Ambiguity resolution WL = 0.15 0.25 1000. 99. 15000. ; FIXDRV, SOLVE Updated for LC_AUTCLN Ambiguity resolution NL = 0.15 0.30 1000. 99. 15000. ; FIXDRV, SOLVE Updated for LC_AUTCLN Yaw Model = Y ; Y/N default = Y Radiation Model for ARC = BERNE Inertial frame = J2000 Elevation Cutoff = 0 ; default 0 to use value in autcln.cmd Tides applied = 31 ; Binary coded: 1 earth 2 freq-dep 4 pole 8 ocean 16 remove mean for pole tide ; 32 atmosphere ; default = 31 Use otl.list = N Use otl.grid = Y Use atl.list = N Use atl.grid = N Etide model = IERS03 ; IERS96/IERS03 Apply atm loading = N ; Y/N for atmospheric loading Use atml.list = N Use atml.grid = N Antenna Model = ELEV ; NONE/ELEV/AZEL default = ELEV SV antenna model = ELEV ; NONE/ELEV default = NONE SV antenna off = Y ; Y/N to estimate satellite antenna Decimation Factor = 4 ; Decimation factor in solve Update tolerance = .05 ; minimum adjustment for updating L-file coordinates, default .3 m Use N-file = Y ; Y/N (default no): automatic procedure to reweight by station Delete AUTCLN input C-files = Y ; Y/N ; default Y to force rerun of MODEL Quick-pre observable = LC_ONLY ; For 1st iter or autcln pre, default same as final, LC_AUTCLN not allowed Quick-pre decimation factor = 10 ; 1st iter or autcln pre, default same as Decimation Factor Bias apriori = 1000. ; Optional constraint on biases for LC_AUTCLN (default 0 -> no constrint) Optional controls: Scratch directory = /tmp Inertial frame = B1950 ; B1950/J2000 (default = J2000) Initial ARC ; YES/NO default = NO for BASELINE/KIINEMATIC, YES for RELAX/ORBIT Final ARC ; YES/NO default = YES Radiation Model for ARC ; SPHRC/BERNE/SRDYB/SVBDY default = SPHRC Reference System for ARC ; WGS72/WGS84/MERIT/IGS92 (default = IGS92) Tabular interval for ARC ; 900. seconds (new default), 1350. seconds (old default) Stepsize for ARC ; 75. seconds (new default), 168.75 seconds (old default) Earth Rotation ; Diurnal/Semidirunal terms: Binary coded: 1=pole 2=UT1 4=Ray model; default=7 Estimate EOP ; Binary coded: 1 wob 2 ut1 4 wob rate 8 ut1 rate Wobble Constraint = 3. 0.3 ; Default 3. (arcsec) 0.3 (arcsec/day) UT1 Constraint = 0.00002 0.02 ; Default .00002 (sec) 0.02 (sec/day) Number Zen = 4 ; number of zenith-delay parameters (default 1) Zenith Constraints = 0.50 ; zenith-delay a priori constraint in meters (default 0.5) Zenith Model = PWL ; PWL (piecewise linear)/CON (step) Zenith Variation = 0.02 100. ; zenith-delay variation, tau in meters/sqrt(hr), hrs (default .02 100.) Gradient Constraints = 0.03 ; gradient at 10 deg elevation in meters Tropospheric Constraints = NO ; YES/NO (spatial constraint) Antenna Model ; NONE/ELEV/AZEL default = NONE Tide Model ; Binary coded: 1 earth 2 freq-dep 4 pole 8 ocean default = 15 Yaw Model ; YES/NO default = YES I-file = N ; Use I-file (Y/N) (default Y) AUTCLN Postfit = Y ; Assume 'Y' if 'Type of analysis = 1-ITER' (autcln.cmd.postfit file also) Delete AUTCLN input C-files = Y ; YES/NO/Intermediate (default no) Quick-pre observable = LC ; For 1st iter or autcln pre, default same as Choice of observable AUTCLN Command File ; Filename; default none (use default options) Delete eclipse data = POST ; ALL/NO/POST (Default = NO) SCANDD control ; BOTH (default) /NONE/FIRST/FULL/IFBAD see manual sec. 5.2 Iteration ; CFILES / XFILES (default) Edit AUTCLN Command File ; YES/NO; default = NO (For clocks, no longer needed) Ambiguity resolution WL ; default = 0.15 0.15 1000. 10. 500. Ambiguity resolution NL ; default = 0.15 0.15 1000. 10. 500. Type of Biases : IMPLICIT (default for quick), EXPLICIT (default for full) H-file solutions ; ALL ; LOOSE-ONLY Station Error = BASELINE 10. 0. ; 1-way L1, a**2 + (b**2)(L**2) in mm, ppm, default = 10. 0. Station Error = UNIFORM 10. ; 1-way L1 in mm, default = 10. Station Error = ELEVATION 4.3 7.0 ; 1-way L1 , a**2 + b**2/sin(elev)**2 in mm, default = 4.3 7.0 Satellite Error = UNIFORM 0. ; 1-way L1 in mm (added quadratically to station error) default = 0. Select Epochs ; Enter start and stop epoch number (applies only to SOLVE) Decimation Factor ; FOR SOLVE, default = 1 Quick-pre decimation factor = 10 ; 1st iter or autcln pre, default same as Decimation Factor Elevation Cutoff = 15. ; For SOLVE, overrides the MODEL or AUTCLN values if they are lower Correlation print ; Threshhold for printing correlations (default 0.9999) Export Orbits ; YES/NO default = NO Orbit id ; 4-char code read only if Export Orbits = YES Orbit Format ; SP1/SP3 (NGS Standard Products) Orbit organization ; 3-char code read only if Export Orbits = YES Reference System for Orbit = ITR93 ; ITR92/ITR91/ITR90/WGS84/MERIT (for SP3 header) Lunar eclipses = Y ; Set = N to turn off lunar eclipses in ARC to match model of GAMIT < 10.2 (default Y) Delete all input C-files ; YES/NO default = NO Delete MODEL input C-files ; YES/NO default = NO Delete AUTCLN input C-files ; YES/NO default = NO Update T/L files ; T_AND_L (default), T_ONLY, L_ONLY, NONE (Applies only to update for full solution after quick) Update tolerance ; minimum adjustment for updating L-file coordinates, default .3 m SOLVE-only = YES ; YES/NO default = NO X-compress = YES ; Uncompress/compress X-files default = NO SCANDD control ; FULL (default), FIRST, BOTH, IFBAD, NONE Run CTOX = YES ; Make clean X-files from C-files default = NO Bias apriori = 100. ; Optional constraint on biases for LC_AUTCLN (default 0 -> no constrint) SOLVE print = Y ; Turn on SOLVE output to screen (default N)